The effect of coupling agent on the mechanical properties of injection molded polypropylene/wheat straw composites

László Lendvai; Amar Patnaik

doi:10.14513/actatechjaur.00677

Authors

László Lendvai Polymer Institute, Slovak Academy of Science, Dubravska cesta, 9, 845 41 Bratislava, 45, Slovakia // Department of Materials Science and Engineering, Széchenyi István University, Egyetem tér 1., Győr 9026, Hungary
Amar Patnaik Department of Mechanical Engineering, Malaviya National Institute of Technology Jaipur Jaipur 302017, India

DOI:

https://doi.org/10.14513/actatechjaur.00677

Keywords:

polypropylene, composites, natural fibers, wheat straw, mechanical properties, injection moulding

Abstract

The objective of this work is to evaluate the effect of maleic anhydride-grafted polypropylene (MAPP) as coupling agent in polypropylene (PP)-based composites filled with ground wheat straw (WS) particles. The WS and the MAPP content in the composites was 10 wt% and 2 wt%, respectively. The samples were fabricated through melt compounding using a twin-screw extruder and then formed into dumbbell-shaped specimens by injection molding. The mechanical properties of neat PP and the composites with and without coupling were evaluated based on tensile and flexural tests and dynamic mechanical analyses (DMA). The experimental results showed that incorporating WS into the PP reduces its tensile strength by ~3 MPa, while improving its Young’s modulus by 0.14 GPa. The addition of MAPP compensated for the loss in tensile strength without affecting the modulus. Similar observations were made during the flexural tests as well, in which case, however, there was no loss revealed in the strength in the presence of WS due to the different types of load. The results of DMA analyses indicated an improved stiffness of WS-containing samples throughout the whole analyzed temperature range of 20-120 °C as a consequence of reduced chain mobility of PP caused by the stiff straw particles.

Downloads

Download data is not yet available.

References

O. Akampumuza, P. M. Wambua, A. Ahmed, W. Li, X.-H. Qin, Review of the applications of biocomposites in the automotive industry, Polymer Composites 38 (11) (2017) pp. 2553–2569. https://doi.org/10.1002/pc.23847

M. S. Huda, L. T. Drzal, D. Ray, A. K. Mohanty, M. Mishra,, Chapter 7, in: K. L. Pickering (Ed.), Properties and Performance of Natural-Fibre Composites, Woodhead Publishing, Sawston, 2008.

S. Tejyan, N. K. Baliyan, V. K. Patel, A. Patnaik, T. Singh, Polymer green composites reinforced with natural fibers: A comparative study. Materials Today: Proceedings 44 (6) (2021) pp. 4767-4769. https://doi.org/10.1016/j.matpr.2020.10.971

J. Karger-Kocsis, Polypropylene Structure, Blends and Composites, Chapman and Hall, London, 1995. https://doi.org/10.1007/978-94-011-0523-1

J. Karger-Kocsis, T. Bárány, Polypropylene Handbook: Morphology, Blends and Composites, Springer International Publishing, Cham, 2019. https://doi.org/10.1007/978-3-030-12903-3

L. Lendvai, A novel preparation method of polypropylene/natural rubber blends with improved toughness, Polymer International 70 (3) (2021) pp. 298-307. https://doi.org/10.1002/pi.6133

I. P. Mahendra, B. Wirjosentono, Tamrin, H. Ismail, J. A. Mendez, V. Causin, The influence of maleic anhydride-grafted polymers as compatibilizer on the properties of polypropylene and cyclic natural rubber blends, Journal of Polymer Research 26 (2019) 215. https://doi.org/10.1007/s10965-019-1878-2

L. Lendvai, Water-Assisted Production of Polypropylene/Boehmite Composites, Periodica Polytechica Mechanical Engineering 64 (2) (2020) pp. 128-135. https://doi.org/10.3311/PPme.13981

S. Panthapulakkal, M. Sain, Injection Molded Wheat Straw and Corn Stem Filled Polypropylene Composites, Journal of Polymers and the Environment 14 (2006) pp. 265-272. https://doi.org/10.1007/s10924-006-0021-8

H. Hargitai, I. Rácz, R. D. Anandjiwala, Development of HEMP Fiber Reinforced Polypropylene Composites, Journal of Thermoplastic Composite Materials 21 (2) (2008) pp. 165-174. https://doi.org/10.1177/0892705707083949

T. Väisänen, A. Haapala, R. Lappalainen, L. Tomppo, Utilization of agricultural and forest industry waste and residues in natural fiber-polymer composites: A review, Waste Management 54 (2016) pp. 62-73. https://doi.org/10.1016/j.wasman.2016.04.037

G. Dogossy, T. Czigány, Modeling and investigation of the reinforcing effect of maize hull in PE matrix composites, Polymers for Advanced Technologies 17 (9-10) (2006) pp. 825-829. https://doi.org/10.1002/pat.748

T. Singh, S. Tejyan, A. Patnaik, V. Singh, I. Zsoldos, G. Fekete, Fabrication of waste bagasse fiber-reinforced epoxy composites: Study of physical, mechanical, and erosion properties, Polymer Composites 40 (9) (2019) pp. 3777-3786. https://doi.org/10.1002/pc.25239

A. Gupta, A. Joshi, S. Tejyan, B. Gangil, T. Singh, Comparative study of mechanical properties of orange peel filled epoxy composites joined by a mechanical fastener, Materials Today: Proceedings 44 (6) (2021) pp. 4671-4676. https://doi.org/10.1016/j.matpr.2020.11.020

M. Zabihzadeh, F. Dastoorian, G. Ebrahimi, Effect of MAPE on Mechanical and Morphological Properties of Wheat Straw/HDPE Injection Molded Composites, Journal of Reinforced Plastics and Composites 29 (1) (2008) pp. 123-131. https://doi.org/10.1177/0731684408096426

M. Duque-Acevedo, L. J. Belmonte-Ureña, F. J. Cortés-García, F. Camacho-Ferre, Agricultural waste: Review of the evolution, approaches and perspectives on alternative uses, Global Ecology and Conservation 22 (2020) e00902. https://doi.org/10.1016/j.gecco.2020.e00902

S. A. Paul, K. Joseph, G. D. G. Mathew, L. A. Pothen, S. Thomas, Influence of polarity parameters on the mechanical properties of composites from polypropylene fiber and short banana fiber, Composites Part A: Applied Science and Manufacturing 41 (10) (2010) pp. 1380-1387. https://doi.org/10.1016/j.compositesa.2010.04.015

M. Chougan, S. H. Ghaffar, M. J. Al-Kheetan, M. Gecevicius, Wheat straw pre-treatments using eco-friendly strategies for enhancing the tensile properties of bio-based polylactic acid composites, Industrial Crops and Products 155 (2020) 112836. https://doi.org/10.1016/j.indcrop.2020.112836

R. Fatoni, L. Simon, A. Elkamel, A. Almansoori, Wheat straw fibre size effects on the mechanical properties of polypropylene composites, The Canadian Journal of Chemical Engineering 92 (10) (2014) pp. 1700-1708. https://doi.org/10.1002/cjce.22032

S. Mohanty, S. K. Nayak, S. K. Verma, S. S. Tripathy, Effect of MAPP as a Coupling Agent on the Performance of Jute–PP Composites, Journal of Reinforced Plastics and Composites 23 (6) (2004) pp. 625-637. https://doi.org/10.1177/0731684404032868

X. Chen, Q. Guo, Y. Mi, Bamboo fiber-reinforced polypropylene composites: A study of the mechanical properties, Journal of Applied Polymer Science 69 (1998) pp. 1891-1899. https://doi.org/10.1002/(SICI)1097 4628(19980906)69:10<1891::AID-APP1>3.0.CO;2-9

L. Zhu, J. Cao, Y. Wang, R. Liu, G. Zhao, Effect of MAPP on interfacial compatibility of wood flour/polypropylene composite evaluated with dielectric approach, Polymer Composites 35 (3) (2014) pp. 489-494. https://doi.org/10.1002/pc.22686

M. Sabri, A. Mukhtar, K. Shahril, A. S. Rohana, H. Salmah, Effect of Compatibilizer on Mechanical Properties and Water Absorption Behaviour of Coconut Fiber Filled Polypropylene Composite, Advanced Materials Research 795 (2013) pp. 313-317. https://doi.org/10.4028/www.scientific.net/AMR.795.313

N. Amir, K. A. Z. Abidin, F. B. M. Shiri, Effects of Fibre Configuration on Mechanical Properties of Banana Fibre/PP/MAPP Natural Fibre Reinforced Polymer Composite, Procedia Engineering 184 (2017) pp. 573-580. https://doi.org/10.1016/j.proeng.2017.04.140

T. Sullins, S. Pillay, A. Komus, H. Ning, Hemp fiber reinforced polypropylene composites: The effects of material treatments, Composites Part B: Engineering 114 (2017) pp. 15-22. https://doi.org/10.1016/j.compositesb.2017.02.001

Y. Zhang, A. E. Ghali, B. Li, Physical Properties of Wheat Straw Varieties Cultivated Under Different Climatic and Soil Conditions in Three Continents, American Journal of Engineering and Applied Sciences 5 (2) (2012) pp. 98-106.

S. Panthapulakkal, M. Sain, Injection Molded Wheat Straw and Corn Stem Filled Polypropylene Composites, Journal of Polymers and the Environment 14 (2006) pp. 265-272. https://dx.doi.org/10.1007/s10924-006-0021-8

D. Pakuszta, M. Jedryczka, M. Binkiewicz, Mechanical properties of polypropylene composites filled with the straw of oilseed rape infested by the fungal pathogen Sclerotinia sclerotiorum, Journal of Composite Materials 47 (12) (2012) pp. 1461-1470. https://dx.doi.org/10.1177/0021998312448498

S. A. Hashemi, M. Esfandeh, J. Mohammadi, Mechanical, Thermal and Rheological Properties of Polypropylene/ Wheat Straw Composites and Study of the Effect of Nanoclay on Their Mechanical Properties, Polymers and Polymer Composites 18 (2) (2010) pp. 67-73. https://dx.doi.org/10.1177/096739111001800202

A. Ashori, A. Nourbakhsh, Mechanical Behavior of Agro-Residue-Reinforced Polypropylene Composites, Journal of Applied Polymer Science 11 (5) (2009) pp. 2616-2620. https://doi.org/10.1002/app.29345

M. Pan, S. Y. Zhang, D. Zhou, Preparation and Properties of Wheat Straw Fiber-polypropylene Composites. Part II. Investigation of Surface Treatments on the Thermo-mechanical and Rheological Properties of the Composites, Journal of Composite Materials 44 (9) (2009) pp. 1061-1073. https://doi.org/10.1177/0021998309349549